Ball Bearing, Industrial Bearings Manufacturer & Supplier - Copland Bearing
Life and load
Home > Life and load

Life & Loads

When in service, even a bearing that is properly lubricated, properly installed, and adequately protected from abrasives, moisture, and corrosive reagents, can fail from material fatigue. Material fatigue is manifested as a flaking off of metallic particles from the surface of a raceway or rolling element. This flaking will eventually cause the bearings to fail. The effective life of a bearing is usually defined in terms of the total number of revolutions a bearing can undergo before flaking of either the raceway surface or the rolling element surfaces occurs.


● Machine applications and requisite life

The requisite life of the bearing is usually determined by the type of machine in which the bearing will be used, duration of service and operational reliability requirements. A general guide to these requisite life criteria is shown in the following table.


● Machine applications and requisite life


Operating condition


service life

Short or intermittent operation

Household electric appliance, electric tools,
agricultural equipment, heavy cargo hoisting

4000 - 8000

Not extended duration, but
stable operation required

Household air conditioner motors,
construction equipment, conveyers,

8000 - 12000

Intermittent but extended

Rolling milI roll necks, small motors, cranes

8000 - 12000

Motors used in factories, general gears

12000 - 20000

Machine tools, shaker screens, crushers

20000 - 30000

Compressors, pumps, gears for essential use

40000 - 60000

Daily operation more than
8 hr.or continuous extended


12000 - 20000

Centrifugal separators, air conditioners, air
blowers, woodworking equipment, passenger
coach axle journals

20000 - 30000

Large motors, mine hoists, locomotive axle
journals, railway rolling stock traction motors

40000 - 60000

Paper manufacturing equipment

100000 - 200000

24 hr.operation
(no failure allowed)

Water supply facilities, power stations, mine
water discharge facilities

100000 - 200000



● Service life of bearing system comprising two or more bearings

Even for systems which comprise two or more bearings,if one bearing is damaged,the entire system malfunctions. Where all bearings used in an application are regarded as one system, the service life of the bearing system can be calculated using the following equation.




● Bearing loads

When calculating bearing load using the loads on a position on the shaft, it is necessary to calculate center distance between the load application points of the bearings. Deep groove ball bearings have load center points at the center line of the width. Single-row tapered roller bearings, have load center points offcenter to the center line of the bearing width.


● Magnitude of load

The magnitude of the load is one of the factors that usually determine the size of the bearing. Generally, roller bearings are able to support heavier loads than similar sized ball bearings and bearings having a full complement of rolling elements can accommodate heavier loads than the corresponding caged bearings. Ball bearings are mostly used where loads are light or moderate. For heavy loads and where shaft diameters are large, roller bearings are usually the more appropriate choice.


Radial load Axial load Combined load
Bearings can only support pure
radial loads.
Bearings are suitable for light or
moderate loads that are purely
A combined load comprises a
radial and axial load acting


● Load acting on shafts

It is possible to calculate theoretical values for these loads. However, there are many instances where the actual operational shaft load is much greater than the theoretically calculated load, due to machine vibration and/or shock. This actual shaft load can be found by using formula



● Load factor fw


Amount of shock fw Application
Heavy shock 1.0-1.2 Electric machines, machine tools, measuring instruments.
Light shock 1.2-1.5 Railway vehicles, automobiles, rolling mills, metal working machines,
paper making machines, rubber mixing machines, printing machines,
aircraft, textile machines, electrical units, office machines.
Very little or no shock 1.5-3.0 Crushers, agricultural equipment, construction equipment, cranes.

Copland (NingBo) Bearing Technology Co.,Ltd

Address: No. 10, Gongyi Road, Zhuangshi Street, Zhenhai District, Ningbo ,China--315201
Tel: +86-574-66605000
Fax: +86-574-66605000